The Protector is designed to allow the intermediate gear to slip on an excessive overload.
| KEY # |
PART # |
DESCRIPTION |
QTY |
| 627-120 |
35627 |
Gear Housing |
1 |
| 627-122 |
982682 |
Gear Housing Attaching Screw |
4 |
| 627-122A |
940830 |
Gear Housing Attaching Screw Lockwasher |
4 |
| 627-124 |
35707 |
Gear Housing Gasket |
1 |
| 627-303 |
35009 |
Liftwheel Gear (Model J, L & R) |
1 |
| |
35639 |
Liftwheel Gear (Model LL & RR) |
1 |
| 627-305 |
35773 |
Liftwheel Gear Nut |
1 |
| 627-306 |
986276 |
Liftwheel Gear Nut Washer |
1 |
| 627-307 |
82002 |
Liftwheel Bearing - Gear End |
1 |
| 627-310 |
35688 |
Drive Shaft & Pinion Sub-Assembly (Includes 627-311 through 627-315) (Model J) |
1 |
| |
35687 |
Drive Shaft & Pinion Sub-Assembly (Model L, LL, R & RR) |
1 |
| 627-311 |
35357 |
Drive Shaft & Pinion (Model J) |
1 |
| |
35356 |
Drive Shaft & Pinion (Model L, LL, R & RR) |
1 |
| 627-312 |
83691 |
Drive Shaft Pinion Bearing |
1 |
| 627-314 |
35744 |
Brake Hub |
1 |
| 627-315 |
35766 |
Brake Hub Snap Ring |
1 |
| 627-321 |
88437 |
Intermediate Gear & Pinion Bearing - Outboard |
1 |
| 627-323 |
35763 |
Intermediate Gear Snap Ring |
1 |
| 627-325 |
35351 |
Intermediate Pinion (Model J, L & R) |
1 |
| |
35420 |
Intermediate Pinion (Model LL & RR) |
1 |
| 627-326 |
83670 |
Intermediate Gear & Pinion Bearing - Inboard |
1 |
| |
24350 |
Intermediate Gear & Pinion Shaft Adapter |
1 |
| 627-327 |
36668 |
Lodestar Protector (Model J) |
1 |
| |
36670 |
Lodestar Protector (Model L & R) |
1 |
| |
36671 |
Lodestar Protector (Model LL & RR) |
1 |
| 627-328 |
3601 |
Lodestar Protector Kit (Includes 627-124, 627-321, 627-323, 627-325 & 627-327) (Model J) |
1 |
| |
3603 |
Lodestar Protector Kit (Includes 627-124, 627-321, 627-323, 627-325 & 627-327) (Model L & R)
|
1 |
| |
3604 |
Lodestar Protector Kit (Includes 627-124, 627-323, 627-327 (Model LL & RR) |
1 |
INSPECTION
To assure safe operation, extra long life and top performance, a regular inspection procedure must be initiated to replace damaged parts.
MAINTENANCE
The Protector should operate for the normal life of the hoist without service.
This device has been lubricated and calibrated at the factory for a specific model of a hoist. It is not adjustable or interchangeable.
For proper overload protection, be sure before installing a Protector that it is correct for the unit. The spring washer of the Protector had been color-coded at the factory. Please refer to the
CM hoist replacement parts user manual - Classic Lodestar (p.11)
CAUTION: The Protector is susceptible to overheating and wear when slipped for extended periods. Under no circumstance should the clutch be allowed to slip for more than a few seconds. Due to the above, a hoist equipped with a Protector is not recommended for use in any application where there is a possibility of adding to an already suspended load to the point of overload. This includes dumbwaiter installations, containers that are loaded in mid-air, etc.
