Classic Lodestar Large Frame - Protector Kit

The Protector is designed to allow the intermediate gear to slip on an excessive overload.
Classic Lodestar Hoist Parts - Large Frame Protector Kit
KEY # PART # DESCRIPTION QTY
627-120 35627 Gear Housing 1
627-122 982682 Gear Housing Attaching Screw 4
627-122A 940830 Gear Housing Attaching Screw Lockwasher 4
627-124 35707 Gear Housing Gasket 1
627-303 35009 Liftwheel Gear (Model J, L & R) 1
  35639 Liftwheel Gear (Model LL & RR) 1
627-305 35773 Liftwheel Gear Nut 1
627-306 986276 Liftwheel Gear Nut Washer 1
627-307 82002 Liftwheel Bearing - Gear End 1
627-310 35688 Drive Shaft & Pinion Sub-Assembly (Includes 627-311 through 627-315) (Model J) 1
  35687 Drive Shaft & Pinion Sub-Assembly (Model L, LL, R & RR) 1
627-311 35357 Drive Shaft & Pinion (Model J) 1
  35356 Drive Shaft & Pinion (Model L, LL, R & RR) 1
627-312 83691 Drive Shaft Pinion Bearing 1
627-314 35744 Brake Hub  1
627-315 35766 Brake Hub Snap Ring 1
627-321 88437 Intermediate Gear & Pinion Bearing - Outboard 1
627-323 35763 Intermediate Gear Snap Ring 1
627-325 35351 Intermediate Pinion (Model J, L & R) 1
  35420 Intermediate Pinion (Model LL & RR) 1
627-326 83670 Intermediate Gear & Pinion Bearing - Inboard 1
  24350 Intermediate Gear & Pinion Shaft Adapter 1
627-327 36668 Lodestar Protector (Model J) 1
  36670 Lodestar Protector (Model L & R) 1
  36671 Lodestar Protector (Model LL & RR) 1
627-328 3601 Lodestar Protector Kit (Includes 627-124, 627-321, 627-323, 627-325 & 627-327) (Model J) 1
  3603 Lodestar Protector Kit (Includes 627-124, 627-321, 627-323, 627-325 & 627-327) (Model L & R) 1
  3604 Lodestar Protector Kit (Includes 627-124, 627-323, 627-327 (Model LL & RR) 1

INSPECTION

To assure safe operation, extra long life and top performance, a regular inspection procedure must be initiated to replace damaged parts.

MAINTENANCE

The Protector should operate for the normal life of the hoist without service.
This device has been lubricated and calibrated at the factory for a specific model of a hoist. It is not adjustable or interchangeable.
For proper overload protection, be sure before installing a Protector that it is correct for the unit. The spring washer of the Protector had been color-coded at the factory. Please refer to the CM hoist replacement parts user manual - Classic Lodestar (p.11)
CAUTION: The Protector is susceptible to overheating and wear when slipped for extended periods. Under no circumstance should the clutch be allowed to slip for more than a few seconds. Due to the above, a hoist equipped with a Protector is not recommended for use in any application where there is a possibility of adding to an already suspended load to the point of overload. This includes dumbwaiter installations, containers that are loaded in mid-air, etc. 
Go Back to
Full Classic Lodestar Hoist Configuration